Recent content by Rides520

  1. R

    The Journey of a wrench and his first motorcycle

    Still keeping the machine rolling. Thought i would ask if the sages hear any subtle clues and looking for a pointer on the idle hang. Is it normal or is it hesitation. Going to make another manometer very soon if not tonight and double check the balance.
  2. R

    The Journey of a wrench and his first motorcycle

    Im pretty certain they are headers that were cut right at the start of the muffler. Or if they made headers that didn't get welded to mufflers at the factory, i got a pair on ebay. Then i put the original slip ons back. This was an attempt to get it back to how i got it. Which i remember running...
  3. R

    The Journey of a wrench and his first motorcycle

    lol try and post a video of the idle and all i do is yap over the duration of the video
  4. R

    The Journey of a wrench and his first motorcycle

    I actually feel pretty stupid asking for help, then getting all defensive. I do have a stroboscope? "Timing light" but the bikes been hacked up pretty bad and im missing the centre stand and probably the mounts to attach on. Need to get me a proper lift.
  5. R

    The Journey of a wrench and his first motorcycle

    Thanks xschris I appreciate the wisdom. The plugs arn't nearly as lean looking after upping the pilots but its starting to look like my midrange is a little rich going to put another tank of gas worth of miles on the current settings and check the overall color again. Idle mix screws are intact...
  6. R

    The Journey of a wrench and his first motorcycle

    Going to hunt for an air leak. My manual puts 142.5 main and 42.5 pilots at stock. Im just trying to be as descriptive as possible and im really only fallowing the factory pro high rpm guide basically to the letter. Using feel as the majority of my post 4k rpm decision making and using plug...
  7. R

    The Journey of a wrench and his first motorcycle

    Blah still lean after 30 miles and im around 4 turns on both. Ive hit the rich part of the fuel screw but i think one size up on both is called for. I might install the 47.5s and use a lower fuel screw out position for the time being. Utilizing lower fuel screws out is totally cool right? I...
  8. R

    The Journey of a wrench and his first motorcycle

    Both cylinders are lean, upping pilots to 42.5. I dont have 45s but i do have 47.5s if needed. Carb sync tomorrow after a "spirited" 10-15 min ride in this +70F weather.
  9. R

    The Journey of a wrench and his first motorcycle

    I religiously sync a warm engine after each change. I might remake my manometer and find mines wildly inaccurate after a bit of use.
  10. R

    The Journey of a wrench and his first motorcycle

    Could use some sage advice. Tested the bike again last night and nothing really jumped out untill about 17 miles in, what i consider is about the time the bike got warm. Was running around the hilly side off town to listen to deceleration and sustained acceleration. Deceleration sounds great...
  11. R

    The Journey of a wrench and his first motorcycle

    It never ends does it? Been awhile and thought i would check in. Since my last update I had a scenerio where i rode the bike all day parked it, pulled plugs looked at the color and buttoned it all up. Had to be at work and could not get the bike to start. I was done! Done i say, i drained the...
  12. R

    The Journey of a wrench and his first motorcycle

    So i'll be doing a total rewire, there are no fuses in the current setup and no thanks that's not right. Super duper excited and if i can fit it into the budget i'll freshen/consolidate some of the older electronics. Found some schematics on here and will be obtaining the wire and space to do it...
  13. R

    '82 XS400SE Idle mixture/pilot screws

    Most success stories and what many would recommend as your start is from 3.25 to 3.75 turns out from lightly seated with 4 being the maximum, haven't heard of a minimum. I kept mine uniform till plug color was leading me to and end result of 2.75 on the right and 3.25 on the left if i remember...
  14. R

    Looking for a specific jetting guide

    I own the pocket tuner but i finally found the website. http://www.factorypro.com/tech/tech_tuning_procedures/tuning_carbtune,CV,high_rpm_engines.html
Back
Top