Recent content by wgnzlz

  1. W

    Help! Cam sprocket

    Oops, forgot that part of his post :doh:
  2. W

    Help! Cam sprocket

    I just went through the same thing this morning. Mine were at about 11 o'clock and 5 o'clock. However, after removing the 5 o'clock bolt, I was able to rotate the sprocket, counter clockwise, just enough to gain access to the other bolt. Good luck.
  3. W

    Just bought a 77 XS360 - First project bike!

    Between moving into a new house, traveling for work and everything involved with have two young children, I haven't been able to spend too much time on the bike. However, I was finally able to spend a couple of hours working on the bike this morning. I was able to get the camshaft cover, cam &...
  4. W

    Just bought a 77 XS360 - First project bike!

    Thanks! I'm sure I'll be asking for help. Right now the work is on hold while I build a workbench, LOL. Didn't think it would be fun doing an engine tear down sitting on the floor.
  5. W

    Just bought a 77 XS360 - First project bike!

    I'm not unfamiliar but this is the first time I'll be tearing one down completely.
  6. W

    Just bought a 77 XS360 - First project bike!

    I finally moved into my new house and was able to get started this past weekend. I spent some time on it Sunday and was able to pull the engine. So far I'm having a lot of fun. I just ordered the gasket set and oil seal kit from ebay. Still need to figure out what to buy to rebuild the carbs...
  7. W

    Recommendation for Lift for tear-down/repaint/rebuild/tires

    I'm looking for the same type of lift to use for both of my bikes. After researching the lift you mention I found a similar lift, looks the same to me other than color, on amazon for $10 cheaper and free shipping. I'd actually like to have the dolly though. Here's the link...
  8. W

    Just bought a 77 XS360 - First project bike!

    Thanks, I'll get one ordered. Will I need the oil seal kit?
  9. W

    Just bought a 77 XS360 - First project bike!

    Thanks for your advice guys. I purchased the crankcase in the second ebay link I posted. It doesn't make sense to try and fix the current case if I can get one in good condition for $35. However, I now have to source all of the gaskets and not sure how difficult it will be to remove and...
  10. W

    Just bought a 77 XS360 - First project bike!

    I don't think the previous owner knew about the issue. However, it still sucks. I see the spot that looks like a crack in the photo and check that area this morning. It isn't cracked and the engine isn't leaking at all. I looked around ebay this morning and this crankcase seems like it would...
  11. W

    Just bought a 77 XS360 - First project bike!

    The weather was nice today so I decided to push the bike out and try cleaning up the engine. While doing so, I found my first surprise. The left front engine mount, on the crankcase, is completely gone. The right side is still there but is very thin. I'm not sure how much material is supposed to...
  12. W

    Just bought a 77 XS360 - First project bike!

    I'm hoping you're right. I currently plan on putting on a set of drag bars and am leaning towards a set of IRC GS-11 tires.
  13. W

    Just bought a 77 XS360 - First project bike!

    I still haven't started restoring my new bike but did take a little time cleaning it today. All I did was spray some foam cleaner all over it then gently hosed it down. I think took a little time cleaning the wheels and bars. It surprised me how easily the wheels cleaned up and they really...
  14. W

    Just bought a 77 XS360 - First project bike!

    Thanks BBS360. I think I'm with you on not making any permanent modifications. After getting it all cleaned up and running well I will probably just put a good set of tires on it and either Euro or Clubman bars.
  15. W

    Just bought a 77 XS360 - First project bike!

    Thanks guys! I'm not sure about the different "trim" levels as I haven't been able to find too much information. The bike rides ok right now, I've taken it for a quick spin around my neighborhood. Also, the guy I bought it from rode it to my house. The clutch needs adjusted as the lever pull is...
Back
Top