Search results

As the title states, need left side controls. Let me know what you have.

I have my wiring harness hooked up enough so I could set the timing. As I was loosening the point, I noticed some smoke (white i think?) coming off the stator. I went to check the fuses and the fuse block was very warm. Only thing I could think of is that I possibly hadn't grounded the existing...

Hey guys. Thought 'd take tonight to time my ignition and try and fire this baby up. My issue is that I'm not getting power to my coils and points (which is the only thing I've hooked up). I think the problem is here. Can someone tell me what this is and if that empty bolt and nut is supposed to...

Quick question. I've noticed a lot of builds where the carb boots have been eliminated. Were they just necessary as an extension to the air boxes and a connection point so that the engine breather could also be filtered with the same system? My plan is pods right to the carbs and a separate...

Hey guys. So this is what my manual says for stock jets. I'm a little confused because I thought the BS34's pilot sizing went from #30 and up, whereas the BS38's started at #15 and up. Can someone please clarify? And while we're at it, main jets i'm looking for the "small round" on...

Hey guys, are the xs360 and xs400 valve/rocker covers interchangeable?

Hey dudes, I messaged this guy who builds custom solid state reg/recs and he said the VRREM7 would work for my xs360. What are your thoughts? http://www.oregonmotorcycleparts.com/Reg_rec_units.html Also, here's some electrical porn...

Hey pals. My old swing arm bushings and bolt sleeve are stuck. They're pretty happy where they are. I've busted off the lip of the old bushings, torched it, drilled it, nada. If I really want these out, I will likely destroy the bolt sleeve in the process. My question is the following. I know...

Anyone going to this? http://www.vrra.ca/?page_id=161

FOUND...

Sorry for the quality of the photo, it was dark. When I bought my 360, the PO gave me these forks along with it because the forks on my bike were a bit pitted. He said they were the same size and I thought nothing more of it. Upon actually inspecting them, they are 35mm forks (my 360 is 33mm)...

Hey guys, Looking for some advice on my engine rebuild. My bike has about 14,000KM on in so as part of my project I'm pulling the engine apart to clean it up and check for problems. My question is, how far should I go with its teardown? I've completely taken the top end apart, opened up every...

http://www.jacobbromwell.com/my-custom-creation

I'm not big into the mods and rockers scene, but thought some of you may get a kick out of this.

Hey guys, this isn't necessarily an xs specific question, but more of a general performance related question. I've seen this particular shock relocation on a few bikes, and short of it looking cool, what does it do for handling? Anyone seen/done/ridden this format before?

Anybody know where I can find a gasket set for an xs360? In the midst of my engine rebuild and would like to have them before I'm ready to put it all back together. Finding a set is proving more difficult than I anticipated.

Hey guys, I'm going to the local cycle salvage yard tomorrow ( http://www.ontariocyclesalvage.com/ ) to try and find a few things. Thought I would offer to see if anyone is having difficulties finding specific parts that I could keep an eye out for. Don't worry, you'll pay what I pay. haha.

Hey all, I've been searching the internet for more information on pma electrical systems. This is more so out of curiosity. Does anyone have an understanding of how it works? Pros/Cons? Can this even be done on an xs360/400? Word.

What's up party people. SO. I'm thinking I'm going to switch my 18" spoke front rim w/disc brake for a 19"er. Here are my questions. I assume that if the rim width is the same, it's okay to swap it, but can I use the same spokes and disc brake? Or would I have to buy new spokes. Now, I...

So, after a week of pain, I can't take it anymore. The bolt on my oil filter housing refuses to budge. I've taken PB BLASTER to it, an impact gun, JB Weld, called a machine shop, and went to a welder to have a wrench welded on, but it's too close to aluminum. I completely stripped the thing...