Easy output (layshaft) bearing replacement possible?

CrazyCabbie

XS400 DOHC Jalopy Owner
Messages
42
Reaction score
0
Points
6
Location
Orillia Ontario, Canada
Hi, I have an '82 Seca with the DOHC motor.

The bearing behind the front sprocket is feeling pretty worn out. I can actually jiggle the sprocket a bit...

Talked to an old Yamaha mechanic the other day, and he said that this bearing can be an issue with high mileage (mine has 69,000kms on it now). He also told me it can be done without splitting the case.

My question is: Does anyone know if it really is possible to pull this bearing straight out the side,
rather than having to remove the engine and split the case?
 
Last edited:
I have no experience with this, but wouldn't it be very strange if you could do that? To me this seems like quite an integral part of your engine, which you shouldn't be able to just take out when you're doing something routine like changing your front sprocket. I hope to be wrong on this one, but my gut feel is that you're gonna have to split the case. How does it look? I'm just curious, could you post a picture?
 
I was thinking the same thing, but the guy I was taking to said it was fairly quick and easy.
I was thinking it might be seated in separate 'bolt-on' carrier piece.

I guess I'm being a bit lazy, heh heh... Maybe I should take a look under there in the next few days and update.
 
I'd look on some of the other Yamaha sites as well - the DOHC XS400 didn't last long in NA, but the 550, 650 and 750 versions are pretty much still around. Some of the more common versions may have more information on how to pull it...
 
Thanks for the tip bentwrench! I found on another forum that the bearing is held in place by a circlip!
Very promising!

Also thanks to 16VGTIDave, I realized I must have overlooked a diagram in the appendix, lol

I checked my (PDF) manual again and sure enough it SEEMS that the sprocket, a collar and a circlip are all that stand in my way!

I just changed my oil, and broke the bank for insurance, so it may be a few weeks, but I'll make sure that I take pictures and post the procedure here.
An old dealership service guy (from the 80s) told me it was possible... Just seemed to good to be true.

Thanks again guys, for helping getting my thinkin' sorted out, lol
 
Still no definate answer to my originally posed question.

I started opening the sprocket area up today, but only got as far as looking at the oil seal.
I was able to spin the layshaft/countershaft, and the bearings feel smooth as glass.

I did however find the source of the front sprocket vibration.

The 'sprocket holder', the keyed plate that bolts to the sprocket and holds it in place is the culprit.
It has deep grooves worn into the faces of it from the splines, allowing a huge amount of play.

Part 26 in the image in my next post, Yamaha #3Y1-17456-00-00
(Just in case anyone else has this issue.)

Its a 3 dollar part, and a really easy fix. Yay!
 
Last edited:
no you have to split the cases, there is a half moon retainer clip (part 31) that keeps the bearing from working in or out and keeps the outer race from spinning in the cases
 

Attachments

  • TRANSMISSION.png
    TRANSMISSION.png
    62.7 KB · Views: 228
Last edited:
Thanks jayel, I agree that one is definately requiring the case to be split, but it's not mine.
Here's a bit of the schematic from the 82 DOHC.

It shows a circlip, and though the bearing appears notched, the Yamaha replacement bearing (on Ebay) appears to be a standard 6305 with no notch. I still wouldn't really think it came out the side unless I saw it myself... That was info from a stranger in a parking lot after all, lol.

Screenshot_2013-04-01-11-34-18-1_zpsd5c96709.jpg
 
Last edited:
I can't keep the models separated on these :doh: but even if it is held like that you'd still have to get the shaft out of the way to get a slide hammer on the bearing and heat the cases up to take advantage of the different metal expansion rates, think it would just be easier to get it over with and split the cases IF needed, sometimes re-inventing the wheel is more trouble than it's worth :laugh: good luck with it :bike:
 
Back
Top