Media added by arfstrom

Navigation

  1. XS400 Originals and Restorations 58
  2. XS400 Choppers 2
  3. XS400 Bobbers 26
  4. XS400 Trackers 14
  5. XS400 Cafe Racers 87
  6. XS400 Slightly Modified 30
Browse albums

Most media items

  1. ThePsuedoMonkey
    238

    ThePsuedoMonkey

  2. TimmyT
    168

    TimmyT

  3. dodger0129
    126

    dodger0129

  4. Philodoxo
    118

    Philodoxo

  5. A
    114

    arfstrom

Media statistics

Categories
6
Albums
1,010
Uploaded media
6,693
Embedded media
5
Comments
518
Disk usage
1.1 GB
Used JB Weld to weld two bolts under the fuse block holder.

Used JB Weld to weld two bolts under the fuse block holder.

  • 0
  • 0
VR fuse block

VR fuse block

  • 0
  • 0
That clutch seems to fit nicely. I know the plates are at minimum tolorances.

That clutch seems to fit nicely. I know the plates are at minimum tolorances.

  • 0
  • 0
You can see I was trying to secure the top screw, and have the body roll under the cross beam, Which helped with keeping enough room for the wires on

You can see I was trying to secure the top screw, and have the body roll under the cross beam, Which helped with keeping enough room for the wires on

  • 0
  • 0
Sprocket

Sprocket

  • 0
  • 0
Clutch Tee not seating when the clutch is released. due to clutch rod put in backwards.

Clutch Tee not seating when the clutch is released. due to clutch rod put in backwards.

  • 0
  • 0
Oil pressure sending unit, was finger tight. Or actually not even.

Oil pressure sending unit, was finger tight. Or actually not even.

  • 0
  • 0
If you zoom in on the clip, you can see I left the clip so you can see the grove its suppose to sit into. then going around the shaft, to the right,

If you zoom in on the clip, you can see I left the clip so you can see the grove its suppose to sit into. then going around the shaft, to the right,

  • 0
  • 0
Clutch shaft with no Shim or circlip

Clutch shaft with no Shim or circlip

  • 0
  • 0
This was my second attempt, till I didn't Measure twice, cut once. the first one was trianglar, and was too close to the Starter relay.

This was my second attempt, till I didn't Measure twice, cut once. the first one was trianglar, and was too close to the Starter relay.

  • 0
  • 0
GEDC0413 8/11/13

GEDC0413 8/11/13

  • 0
  • 0
Shim with Cir Clip.

Shim with Cir Clip.

  • 0
  • 0
July 3rd

July 3rd

  • 0
  • 0
Sprocket on Engine ?dup?

Sprocket on Engine ?dup?

  • 0
  • 0
Apparently my engine oil was lubricating my chain. I put in more than a 3/4 of a quart of oil.

Apparently my engine oil was lubricating my chain. I put in more than a 3/4 of a quart of oil.

  • 0
  • 0
Tobie Arfstrom, with bike

Tobie Arfstrom, with bike

  • 0
  • 0
Okay, removing the old sprocket 8/18/12

Okay, removing the old sprocket 8/18/12

  • 0
  • 0
July 3rd

July 3rd

  • 0
  • 0
Front of bike, with

Front of bike, with

  • 0
  • 0
Mini Engine Guard ABA-4R431-00-00 XS400 SH/H

Mini Engine Guard ABA-4R431-00-00 XS400 SH/H

  • 0
  • 0
New Sprocket on, looking good. except taht the clutch seal looks like it leaking

New Sprocket on, looking good. except taht the clutch seal looks like it leaking

  • 0
  • 0
July 3

July 3

  • 0
  • 0
vise grips, onthe bottom of the bottom hose

vise grips, onthe bottom of the bottom hose

  • 0
  • 0
Oil appears to fresh on all parts

Oil appears to fresh on all parts

  • 0
  • 0
Back
Top